Post-printing hot stamping and punching (below)

The use of different plates followed by hot stamping plates, commonly known as electroplates, was widely used in Hong Kong and had a long history. In the early days of printing, there were so-called typefaces, which were used in letterpress printing and were subsequently used in bronzing. The later letterpress printing was converted to electroplate (ZINC zinc was used as the plate material), and the bronzing industry followed it. In recent years, Hong Kong has also begun to use the magnesium version (Magnesium magnesium as the plate material). The magnesium plate has a variety of thicknesses, and the thicker ones can be etched (Photeched) and deeper. They are used for hot stencils, patterning or impact/striking. (embossing/debossing), the effect will be better, and because it is more durable, the large number of hot stamping does not have to be changed frequently. Another copper alloy (copperalloy) as a plate material, because the hardness is stronger than zinc, magnesium, can retain a better image level, high-definition, reduce the molding surface sand, impress millions of stone can also be. The above materials made of zinc, magnesium and copper alloys are suitable for single-layer hot stamping and punching. (singlelevel, bevelledengraving).
There is also a brass plate (composed of copper, tint and lead) with a thickness of about 7mm. It has a low hardness and can be carved. It is suitable for hand-carving and motor engraving. It is regarded as an engraving plate with distinct layers and is multi-layered. Multi-level, sculptured engraving for special beveled engraving, can be used for punching/debossing, embossing, three-dimensional embossing, or one-time hot stamping with convex/concave, also due to the complicated manufacturing process. The price is very expensive, and depends on the complex requirements of the graphic to determine the price, and the copper plate needs to be carved in foreign countries. There are no manufacturers in Hong Kong for the time being.

Hot stamping Attention to temperature and pressure If you want a good effect of bronzing, you must have a suitable gold foil with good thermal stability, and you must also cooperate with the gilding machine. For example, flat pressing and rolling have different effects, and the temperature and pressure should be matched. With the duration of the hot pressing element.
Temperature - The most suitable temperature for bronzing operations is the ability to imprint a clear texture at the lowest possible level. The platen stamping machine has a heating plate temperature of about 110°C, and a roll-type stamping machine has a temperature of 140°C to 150°C. The most suitable temperature is to be found in the test mode. Excessive temperatures will change the foil stamping paper. Bad and blurred lines.
The pressure-pressure depends on the hardness of the material and the texture of the surface. Surface smooth or soft material, lighter pressure, rough or hard, it can be heavier pressure. The flat pressing hot stamping machine is the synchronous hot pressing of the whole sheet. The hot line of the hot rod machine is the line pressure and then the flat pressure. The rolling machine is similar to the line pressure of the Koo machine.
Stoppage time - based on the shortest possible effect of hot stamping, the time is too long, the gold foil and the hot stamped paper are damaged, and the flash foil will become a matte foil.
There are also patterns to be hot stamping and printing pattern sets are accurate, when using a rolling hot stamping machine or a large area of ​​hot stamping, there is a need to foil the negative film film first reduced to 99.8% to 99.7%, before the arrangement of electricity Edition, so that the electric version is heated and swelled on the heating plate. It turns out that the current scratch-off raffle tickets can also be made using the bronzing method.
The price of bronzing depends on which type of gold foil is used, whether gold foil is wasted, the degree of closure, type of layout, quantity, size, and so on. Therefore, there is no standard calculation method for uniform quotation.
When talking with Mr. Huang Weiqiang of Xinghui Bronzing Screen Printing Co., Ltd., he asked three questions and hoped that experienced people could enlighten me. First, in the case of hot-printing cloth husks, although it has been pressed deeply, hot-foil foils are easily detached.
Second, the printed matter that has passed UV is not hot on gold foil.
Third, try to burn many types of gold foil, embossed on black prints (such as printed cardboard, thin paper, black or full-colored leather paper and hot black foil, will be in a very short time ( For 3 or 4 days or for a longer period of time (3 to 4 months), the shadows will gradually appear, and as time goes by, the more they appear, (the gold foil agents say that they are related to printing ink carbon molecules, so they cannot Guarantee that gold foil will not change with the print).

Posted on